Shrewsbury Sunday 30 Aug 2015, Part 2
 

Enjoy again.

http://www.tractiontalkforum.com/pic...ictureid=26494

http://www.tractiontalkforum.com/pic...ictureid=26495

http://www.tractiontalkforum.com/pic...ictureid=26496

http://www.tractiontalkforum.com/pic...ictureid=26497

http://www.tractiontalkforum.com/pic...ictureid=26498

http://www.tractiontalkforum.com/pic...ictureid=26499

http://www.tractiontalkforum.com/pic...ictureid=26500

http://www.tractiontalkforum.com/pic...ictureid=26501

http://www.tractiontalkforum.com/pic...ictureid=26502

http://www.tractiontalkforum.com/pic...ictureid=26503

http://www.tractiontalkforum.com/pic...ictureid=26504

http://www.tractiontalkforum.com/pic...ictureid=26505

http://www.tractiontalkforum.com/pic...ictureid=26506

http://www.tractiontalkforum.com/pic...ictureid=26507

http://www.tractiontalkforum.com/pic...ictureid=26508

http://www.tractiontalkforum.com/pic...ictureid=26509

http://www.tractiontalkforum.com/pic...ictureid=26510

http://www.tractiontalkforum.com/pic...ictureid=26511

http://www.tractiontalkforum.com/pic...ictureid=26512

http://www.tractiontalkforum.com/pic...ictureid=26513

http://www.tractiontalkforum.com/pic...ictureid=26514

http://www.tractiontalkforum.com/pic...ictureid=26515

http://www.tractiontalkforum.com/pic...ictureid=26516

http://www.tractiontalkforum.com/pic...ictureid=26517

http://www.tractiontalkforum.com/pic...ictureid=26518

http://www.tractiontalkforum.com/pic...ictureid=26519

http://www.tractiontalkforum.com/pic...ictureid=26520

http://www.tractiontalkforum.com/pic...ictureid=26521

http://www.tractiontalkforum.com/pic...ictureid=26522

http://www.tractiontalkforum.com/pic...ictureid=26523

http://www.tractiontalkforum.com/pic...ictureid=26524

Three Marshall tractors, all with different front wheels....

yes, mine are Tasker, off a timber drug rather than an engine.

The correct diameter, width and number of spokes. The hub isn't quite right but not a bad match.

Here are the pair mine left the factory with

http://www.steamscenes.org.uk/tti/14/thumb/008_1345.jpg

Not sure what Neils are, but he has done a lot to them to make the hubs a near match.

Marshall tractor front wheels being very scarce, though I expect there is a pair at Dorset as usual, on the front of an Aveling showmans conversion.

The same type of front wheel was fitted to some of the early Marshall I/C tractors.

Anthony just to complete the picture. My front wheels are Aveling traction wagon front wheels, correct number of 10 spokes and a very similar pattern of hub to the Marshall. These hubs have been machined to take the correct pattern Marshall C.I. hub bush. This bolts to the hub on the inside and carries the screw on hub-cap. The diameter of the wheel including the solid rubber is the same as the original steel wheel at 40". This is the maximum size that can fitted and still get full lock. Virtually all of the original tractors finished their working lives as rollers and their original tractor wheels were lost decades ago. The only Tractors with original wheels are Jingling Geordie at Snibston still on steels and one in Ireland on rubbers. These two both have different wheels. Hope this clears things up.

Mine are 40inch without the rubber. And they rub the tank on full lock

I can't tell you how big my wheels are, but I can go to full lock without hitting the belly tanks.

I have been told by a few people (last weekend) that they look like Wallis and Stevens wheels.

Arial

The eagle eyed may have noticed that "Panther" has odd front wheels

Do you know more about that Andy? Or is it just how it left W&S?

Presumably swapped off one of the others e.g Wanda?

Wanda's wheels as far as I'm aware are the same. Have uploaded photos to show the difference.


Sent from my iPad using Tapatalk HD